SuperTectum
TopCoat 440

 
SuperTectum
TopCoat 440
One-component, aliphatic, polyurethane finish coating
One-component polyurethane finish coating which comprises a specific inorganic filler, when combined with a small amount of pigment paste provide excellent coverage power. This allows minimal material consumption and the unnecessity of the second coating (in the case of simple protection against ultraviolet radiation, and not mechanical resistance), which reduces the cost of works. The material is designed with similar elastomeric properties that other products SUPERTECTUM have, allowing to interact and be united with them.
The material is based on pure elastomeric hydrophobic polyurethane resin, which provides excellent mechanical, chemical, thermal, UV resistance properties.
Application area

• Finish coating for SUPERTECTUM materials
• Finishing coating for bulk industrial floors
• Protection of concrete and metal structures.
Features and benefits
Strong and uniform adhesion to all types of surfaces
Excellent coverage power even in one coat
Resistant to automobile loads
High hydrophobicity
Highly resistant to climatic changes, remains elastic at -30° С

Heat resistance, resistance to ultraviolet radiation, not yellowing, not peeling, does not become soft at 80° C
Application procedure
1
Requirements for a concrete substrate (standard):
• Hardness of concrete: R28 = 15Mpa.
• Concrete humidity: W <10%.
• Temperature: 5-35o C.
• Relative humidity: <85%.
2
Seal cracks, damage, holes with suitable material. The substrate must be dry, chemically neutral, even, strong - without cracks and damage, clean - without dust, rust or flaking particles. Traces of contamination from oil, oil substances or chemicals must be removed.
3
Immediately before use, mix the material until a homogeneous mass is formed with a low-speed mixer (up to 300 r/min). A small precipitate may be formed in the bucket after prolonged storage. Mixing must be done very carefully, especially along the walls and bottom of the bucket, until the mixture is completely homogeneous, while trying not to add air into the material, which can lead to the formation of bubbles on the cured coating.
4
Drawing is performed manually using the roller, brush and or apparatus of airless spraying (operating pressure of >200 bar). Apply within 24-72 hours after SUPERTECTUM products.
5
When used as a finishing layer - color protection, small and constant pedestrian load - material consumption 150 g/m2 in one layer.
When used as a finishing layer - color protection, average pedestrian traffic loads and small - flow material 600 g/m2 in two layers and with the mandatory adding of silica sand. The waiting time between layers is not more than 48 hours.
When used as a protective layer of concrete, flow rate is up to 300 g/m2 in two layers. The waiting time between layers is not more than 48 hours.
6
It is not recommended to apply the material in one thick layer.
General information
Packaging
20 kg, 5kg
Shelf life
It can be stored for 12 months minimum in the original unopened buckets in dry places and at temperatures between 5°C to 25° C. Once opened, use as soon as possible.
Safety information
Contains volatile flammable substances. Use in a well-ventilated, non-smoking room away from open flame. Indoors, use a ventilator and activated carbon face masks. The MSDS (Material Safety Data Sheet) is available on request.
Technical specifications
In liquid form (before use):
Properties
Units
Method
Specification
In viscosity (Brookfield)
cP
ASTM D2196-86 at 25°C
400 – 600
Specific gravity
gr/cm3
ASTM D1475 / DIN 53217 / ISO 2811 at 20°C
1.2
Cure Time at 77 ° F (25 ° C) and 55% RH
hours
-
6 – 8
Reapplication Time
hours
-
12 – 48
In cured form (after use):
Properties
Units
Method
Specification
Operating temperature
oC
-
-30 to 80
Maximum temperature for a short time (shock)
oC
-
200
Hardness
Shore D
ASTM D2240 / DIN 53505 / ISO R868
40
Tensile Strength at break at 23° C
Kg/cm2
(N/mm2)
ASTM D412 / EN-ISO-527-3
400
(40)
Elongation at 23° C
%
ASTM D412 / EN-ISO-527-3
>300
Water vapor transfer
gr/m2• h
ASTM E96 (Water Method)
0.8
QUV Accelerated weathering test (4 hours UV, at 60° C (UVB lamps) and 4 hours COND at 50° C)
-
ASTM G53
passed
(2000 hours)
Hydrolysis (potassium hydroxide 8%, 10 days at 50° C)
-
-
no significant elastomeric property change
Hydrolysis (sodium hypochlorite 5%, 10 days)
-
-
no significant elastomeric property change
Get TDS on this material
ANT ALLIANCE is an exclusive supplier of SUPERTECTUM products worldwide.